Resetting IP address...
Preferences dialog
Connection Failed: No DHCP offers received.
For more detailed help, consult the wicd-curses(8) man page.
Connection Failed: Bad password
Unable to connect to wicd daemon DBus interface. This typically means there was a problem starting the daemon. Check the wicd log for more information.
Verifying access point association...
Always show wired interface
Could not connect to wicd's D-Bus interface. Check the wicd log for error messages.
Path to PAC File
Always switch to wired connection when available
Disconnect from all networks
Wired Networks
Changes to your backend won't occur until the daemon is restarted.
Stop a network connection in progress
Connecting
Run pre-disconnect script
To avoid various complications, wicd-curses does not support directly editing the scripts. However, you can edit them manually. First, (as root)", open the "$A" config file, and look for the section labeled by the $B in question. In this case, this is:
You can also configure the wireless networks by looking for the "[<ESSID>]" field in the config file.
Once there, you can adjust (or add) the "beforescript", "afterscript", and "disconnectscript" variables as needed, to change the preconnect, postconnect, and disconnect scripts respectively. Note that you will be specifying the full path to the scripts - not the actual script contents. You will need to add/edit the script contents separately. Refer to the wicd manual page for more information.
You must enter your password to configure scripts
DNS domain
Connection Cancelled
Scanning networks... stand by...
Password
Wicd daemon unreachable
Use Static DNS Usar DNS estático
Setting broadcast address...
Select or create a wired profile to connect with
To connect to a wired network, you must create a network profile. To create a network profile, type a name that describes this network, and press Add.
Press ESC to cancel
Scanning
Flushing the routing table...
Brought to you by:
Refresh network list
Select Hidden Network ESSID
External Programs
Connect Conectar
Display this help dialog
Use global DNS servers
This network requires encryption to be enabled.
Use last used profile on wired autoconnect
Preferences
Connection Failed: Unable to Get IP Address
Setting static IP addresses...
Connecting to daemon...
Automatically connect to this network
Add a new wired profile
DHCP Client
Use dBm to measure signal strength
Use these settings for all networks sharing this essid
Configure Selected Network
Enable debug mode
Removing old connection...
Could not find a graphical sudo program. The script editor could not be launched. You'll have to edit scripts directly your configuration file.
Wireless Networks
Configuring preferences for wired profile "$A"
No wireless networks found.
Check if using madwifi/atheros drivers
Properties
Setting encryption info
About Wicd
OK
Set up Ad-hoc network
Select scripts
Invalid address in $A entry.
Configuring wireless interface...
Generating PSK...
Validating authentication...
ESSID
Anonymous Identity
Wireless Interface
Hidden Network
Key
Wicd Curses Interface
Debugging
Use Encryption
WPA Supplicant
Global DNS servers
Not connected
Done connecting...
Can't connect to the daemon, trying to start it automatically...
Cancel
All controls are case sensitive
Gateway puerta de acceso
Backend
DBus failure! This is most likely caused by the wicd daemon stopping while wicd-curses is running. Please restart the daemon, and then restart wicd-curses.
Terminated by user
Wired Link Detection
Add a new profile
Activate Internet Connection Sharing
Create an Ad-Hoc Network
Putting interface up...
Global DNS has not been enabled in general preferences.
DNS DNS
Advanced Settings
Username
Automatic (recommended)
Wired connection detected
Netmask máscara
Choose from the networks below:
Connect to selected network
wicd-curses does not support deleting the last wired profile. Try renaming it ('F2')
General Settings
Connected to $A at $B (IP: $C)
EXCEPTION! Please report this to the maintainer and file a bug report with the backtrace below:
Configuring preferences for wireless network "$A" ($B)
Generating WPA configuration file...
Search domain
Required encryption information is missing.
Obtaining IP address...
The wicd daemon has shut down. The UI will not function properly until it is restarted.
Setting static DNS servers...
Automatically reconnect on connection loss
Use Encryption (WEP only)
Wired Autoconnect Settings
Run script before connect
You should almost always use wext as the WPA supplicant driver
Network Interfaces
Use default profile on wired autoconnect
Scan
IP IP
Connected to wired network (IP: $A)
WPA Supplicant Driver
Wicd needs to access your computer's network cards.
Wireless Kill Switch Enabled
Hidden Network ESSID
Secured
Putting interface down...
Authentication
Run script after connect
Prompt for profile on wired autoconnect
Channel
Unsecured
Rename wired profile
The wicd daemon is unavailable, so your request cannot be completed
Stop Showing Autoconnect pop-up temporarily
Scan for hidden networks
Use Static IPs us IPs est
use urwid's raw screen controller
Route Table Flushing
Scripts
Identity
Automatic Reconnection
Wired Interface
Press F8 or Q to quit.
Use as default profile (overwrites any previous default)
Wired Network
DNS server
Notifications
Display notifications about connection status
Connection established
Disconnected
Establishing connection...
Connection failed: Could not contact the wireless access point.
Unable to contact the Wicd daemon due to an access denied error from DBus. Please check that your user is in the $A group.
Disconnecting active connections...
ERROR: wicd-curses was denied access to the wicd daemon: please check that your user is in the "$A" group.
Run post-disconnect script
Resume script
Suspend script
Invalid IP address entered.
Ping static gateways after connecting to verify association
$A $B $C $D $E KB/s $F KB/s
$A $B KB/s $C KB/s
Wireless SSID: Speed: IP: Strength: RX: TX:
Wired IP: RX: TX:
To prove you are a human, type the name of the software you are translating (hint: it starts with a "w") in the box below backwards (ie, d..w).